What did you do in your garage today..?

Forum Sponsor
So, what does every new to me bike need?

Farkles.... yes, I know I have a problem....

Who wants common plastic fenders?

2.jpg

3.jpg


When you could pay a bunch of money for carbon ones that do the same thing...

1.jpg

4.jpg

5.jpg

I also have some LighTech wheel adjusters to go on, but apparently I do not have the right socket for the rear wheel. So that is now for another day.

6.jpg
 
I discovered a coolant leak on today's ride. Tired old bike. ZX10R with 156k on it.

I've kinda suspected something's up towards the end of last season ... coolant overflow bottle filling up, sometimes seeing a stream of bubbles inside it ... thinking head gasket leak ... but it sure doesn't run nor act like an engine with a blown head gasket. Yesterday I smelled coolant. This morning I spotted a drop of coolant sitting on one of the coolant pipes. After today's ride - which ended with smelling coolant! - I looked around carefully and shone a flashlight up into the vicinity of the radiator ... and there's visible coolant near the top where one of the upper radiator mounts is attached. The radiator fins were soaked with coolant below this point. Poking around on the forums suggests that it isn't uncommon for the radiator to crack there.

Dammit ... but this is better than dealing with a head gasket.

Seems that aftermarket radiators are fairly readily available. Thinking of buying the aftermarket one ($150ish) and perhaps having the original one repaired if possible. New OEM radiator is available, but $1200+. I'm going to sleep on this. Maybe during the bad weather over the next couple of weeks, I'll take the original one off the bike and see what's up with it.
 
Brian P said:
I discovered a coolant leak on today's ride. Tired old bike. ZX10R with 156k on it.

I've kinda suspected something's up towards the end of last season ... coolant overflow bottle filling up, sometimes seeing a stream of bubbles inside it ... thinking head gasket leak ... but it sure doesn't run nor act like an engine with a blown head gasket. Yesterday I smelled coolant. This morning I spotted a drop of coolant sitting on one of the coolant pipes. After today's ride - which ended with smelling coolant! - I looked around carefully and shone a flashlight up into the vicinity of the radiator ... and there's visible coolant near the top where one of the upper radiator mounts is attached. The radiator fins were soaked with coolant below this point. Poking around on the forums suggests that it isn't uncommon for the radiator to crack there.

Dammit ... but this is better than dealing with a head gasket.

Seems that aftermarket radiators are fairly readily available. Thinking of buying the aftermarket one ($150ish) and perhaps having the original one repaired if possible. New OEM radiator is available, but $1200+. I'm going to sleep on this. Maybe during the bad weather over the next couple of weeks, I'll take the original one off the bike and see what's up with it.
Click to expand...
If you decide to go with OEM, what about low mileage used rad off ebay?

I did that for an '86 VFR with similar mileage and it worked great.
 
Mad Mike said:
I’m religious with oil changes, particularly on late model pickups because they are all sensitive to dirty oil. I blow out air filters as part of my LOF routine so even on my rougher than normal travels, I’ll go 40k on a good air filter.

I’m not much of a F150 fan and would never have one as a work truck, but ironically my daily is an F150 (fortunately its toughest work is getting coffee). I change oil and filter every 6000km, the old coyote has 250k on her and she has 195-205 psi on all cylinders (like new), and quiet phasers.
Click to expand...
Your posts are making me weary of following the service manual for oil changes on my little Mav. Thinking I should do them every 5-8k instead just to be safe.
 
mimico_polak said:
Your posts are making me weary of following the service manual for oil changes on my little Mav. Thinking I should do them every 5-8k instead just to be safe.
Click to expand...
6k is my max, I treat Canadian winters as ‘severe duty’.

My F’d150 has 250k on the clock, religious oil changes and it’s tick free, no phaser noise ant tight timing chains on its Coyote. My Jeep Commander 3.7 just crossed 325k same - engine is as tight as new.

Another tip: many modem engines (all Fords, Hemis, and most GM) are very picky about the first number in the oil type. If it says 0w or 5w, never change to 10w.
 
I’ve soldered a couple of ATV rads over the years using low melt aluminum solder. If you land braze - it’s easy and I’ve never had a fail afterward.
 
Mad Mike said:
Yes - our trucks are in a very challenging severe service environment in the far northern reaches of Ontario. Rough clay/mud roads, -30 for months on end. It’s still -5 (as in your pic) some days in early June.

You don’t see many Ford trucks here - if you do they rarely last 3 years - they can’t take the rugged terrain or the cold. We’re lucky to see 50k from an F150, most are dead in 3 years and rarely hit 100k.

It’s Dodge and GM country, Fords come here to die.

The main Ford issues (F and E series) are cold related. Broken door latches are so common we keep a box of spares for 2 trucks - both inside and out. They don’t start reliably below -30 without being plugged in, and they often go into starter lock out from cranking. You can’t heat them up at idle and they idle all day. They don’t produce enough engine heat or oil flow at idle to serve the cam phasers (or warming spots for the crews) that’s the killer. The ABS /Traction control sensors freeze and the trucks go into limp. These are not random problems - they happen to every late model F and E series gas truck that operates here.

Some owners zip tie the gas pedals to keep idle at 1100rpm to build heat and oil flow. Ford has a hidden high idle setting, but it’s got to be enabled in the BCM using a programmer. It’s a PIA to use - every time you stop: enable the parking brake, turn on cruise control, then simultaneous press of the set and resume buttons. Awful when a bunch of guys use the truck because they have to remember the sequence and to turn it on. Awful because F series parking brakes freeze ON in the cold so nobody will touch them. I do an upgrade that bypasses the control part to keeps the high idle always on - it helps, the engines live to 80-100k.

Dodges and GMs live till they rust out or get crashed. Fords tap out early here - 3 years and 50k is all you get from a work truck.

A fleet manager spelled it out clearly for me:
Ford designs F-150s primarily as consumer pickups with work capability, GM and Ram still design theirs primarily as work trucks that consumers buy.
Click to expand...
Mad Mike said:
I’m religious with oil changes, particularly on late model pickups because they are all sensitive to dirty oil. I blow out air filters as part of my LOF routine so even on my rougher than normal travels, I’ll go 40k on a good air filter.

I’m not much of a F150 fan and would never have one as a work truck, but ironically my daily is an F150 (fortunately its toughest work is getting coffee). I change oil and filter every 6000km, the old coyote has 250k on her and she has 195-205 psi on all cylinders (like new), and quiet phasers.
Click to expand...

I don't have the knowledge of trucks to confirm or refute your statement about Ford vs Chev vs Dodge.
My father did have a '63 Chev with the floor rusted out that would start up and run fine in the worst snowstorms. Just watch out for puddles.
I also have an almost retired contractor friend with 250,000 km on his Ford work truck.
Then there's this poor sod:
 
Amazon says the new radiator has shipped, so I did the messy job of pulling the stock cooling module out. It's in rough shape, not that this surprises me one bit.
 
Baggsy said:
I don't have the knowledge of trucks to confirm or refute your statement about Ford vs Chev vs Dodge.
My father did have a '63 Chev with the floor rusted out that would start up and run fine in the worst snowstorms. Just watch out for puddles.
I also have an almost retired contractor friend with 250,000 km on his Ford work truck.
Then there's this poor sod:
Click to expand...
You’re gonna get sensational issues with any brand of vehicle. My experience comes from working in severe service environments, I drive an F150 myself, 255k on her and runs like new. It’s a decent truck, but has a few weak points. I’d buy another as a daily driver, never for extreme service.

I spend a lot of time in the far north of Ontario. Most pickups here don’t do heavy work (no hauling, trailering, or heavy loads), or get a lot of miles but they travel slowly on rough and snowy roads, idle for hours ant a time, and operate in extreme cold. I can tell you it’s not F150 territory… they come here to die - the cold is a killer on F150 engines, transmissions, electronics and light mechanical parts like plastic interior trims, switches, heaters, and door handle hardware. The rough roads are killers on F150 ball joints, hubs, and leaf springs.
 
Soulcatcher668 said:
So, what does every new to me bike need?

Farkles.... yes, I know I have a problem....

Who wants common plastic fenders?

View attachment 77903

View attachment 77904


When you could pay a bunch of money for carbon ones that do the same thing...

View attachment 77905

View attachment 77902

View attachment 77906

I also have some LighTech wheel adjusters to go on, but apparently I do not have the right socket for the rear wheel. So that is now for another day.

View attachment 77907
Click to expand...

Do you do all the maintenance/oil changes yourself?

I heard that that some of these European models require the dealer to reset the oil life monitor/indicator?
 
POWERMAN said:
I heard that that some of these European models require the dealer to reset the oil life monitor/indicator?
Click to expand...

My Guzzi service reminder light comes on every ̶6̶,̶0̶0̶0̶k̶m̶s̶ 10,000kms. It can only be reset by the dealer, or perhaps DIY using some very expensive equipment.

So, the light will stay on forever. I call it "The Guzzi Golden Wrench Award", given to those who perform their own service.
 
Last edited:
POWERMAN said:
Do you do all the maintenance/oil changes yourself?

I heard that that some of these European models require the dealer to reset the oil life monitor/indicator?
Click to expand...
I took the M in when I got it just to make sure all the firmware was up to date and have them do a once over.
They actually found an issue with the water pump and replaced it under warranty.

I may buy the reset tool..... the jury is still out.
 
Jayell said:
My Guzzi service reminder light comes on every ̶6̶,̶0̶0̶0̶k̶m̶s̶ 10,000kms. It can only be reset by the dealer, or perhaps DIY using some very expensive equipment.

So, the light will stay on forever. I call it "The Guzzi Golden Wrench Award", given to those who perform their own service.
Click to expand...
You should be able to clear the codes, try this:
  1. Turn ignition to ON
  2. Use the MODE button on the left handlebar to open the menu and scroll to Diagnostics.
  3. Enter the service code 12425
  4. Select Service Coupon Reset
  5. Confirm.
The light and or message should disappear.
Forum Sponsor
 
You must log in or register to reply here.
Back
Top Bottom