Search results

Thanks for all the replies! Now I know not to waste anymore time looking for a bit that doesn't exist! 😀

Hey everyone, I’m trying to unscrew some table leveling feet (they're rusted and stuck), and I’m having trouble figuring out what kind of bit I need to remove it. It’s not a Phillips, hex, Robertson, ECX1or2. The inside is kind of cone shaped. I’ve attached a close-up photo of the screw...

Last year, my parked bike was involved in a hit-and-run. The ********* knocked my bike over with his pickup. (The guy was later found and charged. I had his plates and security cam footage of the entire incident.) Anyway, the estimate for repairs is more than the value of the bike, so my...

Pictures are when I saw them before deciding to get them. Will be using them for different events I organize. Now the challenge is to find a better way to tear these puppies down, because they're so big!

That would explain a lot! Thx for the insight. Maybe something to consider! I'm pretty sure it's particle board. The underside got wet from the rain and some of the edges are now swollen and warped (still useable, though). Hmmm...depends on the solution. Now that I think about it...

We actually store the tables on the second floor balcony. It's a pain getting them out there and back into the space, but it seems to work...until I looked at one of the tables today. They are covered with a tarp. However, some water leaked into one, and now there's some water damage on the...

It would be taken apart frequently (once or twice every week, during busy times). I was thinking about 4 pieces, cut along the glued joints, so it would keep the pieces relatively intact. The joints at the ends are angled, too, so might be tricky to cut. Some have proposed just cutting the...

Carpenters, am in need of a solution! ? We have two long tables (126" in length) that we want to be able to dismantle and put back together for easier transport. The thing is, there's no visible screws, and all the joints have been glued together. The table itself is made of particle board...

PM/DM sent!

Only for fellow bikers.

Whoa! Nice setup, dudes! :love:

Hey dudes! Any DJs here? We need one for tomorrow (Thurs) from about 6pm to 11pm. We just started a DJ night every Thurs. Reply here or DM/PM me.

I use Carry Tel for both my business and had got my folks switch over to it. Carry Tel uses the Rogers network. Would recommend. Customer service is responsive. They even call you back a day or two later to follow up. Had issues with modem. They replaced it. But had to go all the way to...

Yes, that's a good point, too! Guess getting a cable installer's the way to go. If anyone has any recommendations, I'd love to know. Thx everyone!

Ok, thanks, GreyGhost. Will look into this wireless bridge. I'm assuming that's what moarmoto linked to. I've also contacted a cable installer to get a quote.

Hmmm, I'm not sure. Our system was to be wired like this: https://drive.google.com/open?id=1I96hyGraFrcJJw52VqR608wnoLisjmrb Now, it's wired so the server (Airport Extreme) has to be in the basement. And, the upstairs (Floor 2) doesn't seem to be connected with either the Main floor or...

Good point about testing! I actually was testing and setting it up last night. Spent a good 5+ hours trying out many different configurations. I'm pretty sure I know what the problem is. It's just trying to reconfigure the cables through floor, walls, and ceilings that is going to be the...

We have a POS that needs to be wired over 3 floors via ethernet cables. Can anyone recommend someone? We had it done by someone else, but they didn't do it as requested. Anyway, we need this done ASAP. Please help! Thanks, dudes! PS-Or, is there a wireless option? It's being used...

Thanks, dudes, for the advice and opinions! Very helpful and appreciated! When I posted, I was having a bad day. Everything seemed like it was going downhill. It's not as bad today, but things are still stressful. Every decision/issue, no matter how small, seems like a catastrophe just...