Mad Mike
Well-known member
They are underway. Look behind the boats -- forward motion levels the chop in their wake.
Boat Rentals
- Thread starter mimico_polak
- Start date
Check the colours of the running lights.
Where would one find a good deal on some marine plywood. Or is that even necessary in my case?
I am wanting to redo the flooring and other paneling of my boat and redo the carpeting on it. The current plywood is PT but im thinking marine grade will be better. Mind you, this plywood is probably 20 years old. Some section have become soft to step on and the carpet is worn out.
This is a custom made job by the PO (family friend). All secured with stainless steel nut/bolt and screws where necessary. The easy part is that there is no guess work on measurements as I can trace the exiting panels and cut. The hard part will be removing the nuts/bolts cause all the ends of the bolt thread had been scored to prevent the nuts from unscrewing.
paging @crankcall
I am wanting to redo the flooring and other paneling of my boat and redo the carpeting on it. The current plywood is PT but im thinking marine grade will be better. Mind you, this plywood is probably 20 years old. Some section have become soft to step on and the carpet is worn out.
This is a custom made job by the PO (family friend). All secured with stainless steel nut/bolt and screws where necessary. The easy part is that there is no guess work on measurements as I can trace the exiting panels and cut. The hard part will be removing the nuts/bolts cause all the ends of the bolt thread had been scored to prevent the nuts from unscrewing.
paging @crankcall
I recarpeted my boat when I got it. Cost me a couple hundred and a day. It's held up well. Iirc I glued it down with spray contact cement. Thankfully the wood was OK and I didn't need to replace it.
The current carpet is wrapped around the existing panels so they need to be removed for recarpeting.
I found a deal in a marine grade carpet for $100. 6 x 23. I think that's a decent deal.
So plywood time, actual marine grade ply has no interior core void ( missing knots) so it’s structural and won’t come apart. PT and exterior sheathing grade ply is made with the same phenolic glue and it’s water proof . The things is sheathing ply and PT is often a bit bowed but screws and bolts fixes that . Marine ply is often mohogany / sapelle or fir so it’s pretty flat , but you don’t actual need it for what you’re doing . Home Depot exterior ply will work for the next 20 yrs .
There are no good deals on actual marine ply , Noah’s in Mississauga has it , exotic in Burlington or Woodshed in Smithville, but they are all $200 a panel.
McFadden in Oakville west should have it , still $200 a panel
Sent from my iPhone using GTAMotorcycle.com
There are no good deals on actual marine ply , Noah’s in Mississauga has it , exotic in Burlington or Woodshed in Smithville, but they are all $200 a panel.
McFadden in Oakville west should have it , still $200 a panel
Sent from my iPhone using GTAMotorcycle.com
Mad Mike
Well-known member
I use exterior grade ply when repairing wood in boats - Home Depot 5/8 for floors, 3/4 for seats tops and foredeck.
I always paint the repair panels with epoxy floor paint, sides and edges. You can use the cheap stuff designed for concrete garage floors.
When tracing old panels, just cut the carpet back 1” on each edge (save time). I like polyolefin outdoor carpet from Home Depot. Good price, and goes down with outdoor carpet glue.
I change fasteners to the ones used on pontoon boats. Way better than nuts and bolts. https://www.amazon.ca/Stainless-Sel...c5ead2c4602e399b8181e465cf747605&gad_source=4
For the nut and bolt hinges, use regular stainless and nylock nuts. Don’t bother peen or score stainless - they will break or strip heads before coming loose. I’d just use a zip cut wheel and a grinder to cut the loose on the underside.
Last edited:
Just consider if your putting a stainless fastener into an aluminum boat , go buy a tub of Tef-gel . Permatex corrosion antiseize also works but that crap gets all over everything.
The manufacturer does not use it when making boats , because in the 5 yr warranty they will never have to F with that fastener again. But you might .
Sent from my iPhone using GTAMotorcycle.com
The manufacturer does not use it when making boats , because in the 5 yr warranty they will never have to F with that fastener again. But you might .
Sent from my iPhone using GTAMotorcycle.com
I was thinking of using the 3/4 on the main floor and the upper deck where there is standing room. And maybe the 5/8 for the side walls and all other hatches etc.
As for carpet I was thinking of using the Vevor marine carpet. Looks like it has a rubber backing that should be easy to glue onto the wood.
I may also consider the foam flooring for the main floor area just for esthetics. But they come in a max width of 48 inches and I need just slightly over 5 ft. I wouldn't like to join to sections but I may have to if I got this way.
Any opinions on this foam flooring stuff.
The existing panels are fastened to aluminum angle corners with nut and bolt where both sides are accessible. Most nuts are just plain nuts with the bolts cut to just past the nut and the last thread scored or hammered. This will make things difficult for removal and reuse of bolts, possibly damaging both and may not be reused. There are some nylon nuts.
I like the self tapping screws MM suggested but I feel like they may be an issue in areas where the back side is accessible and where hands will be looking for things and may get scratched by the tip.
I would like to reuse the exiting bolts but it may not be worth the hassle to repair the thread and trying to match up the length in the area being used.
I think I will just order a bunch of new bolts/scresws.
Lots to think about for this winter project but knowing me I will get busy with other stuff and this will get put on the back burner.
Unless they are a really large or specialty bolt I’m a big fan of new fasteners , the hours spent recycling isn’t worth it ( for me) . Not all stainless is created equal and some Chineseum product isn’t much better than zinc coated . I like those self tappers and your right , they can be knuckle rippers if it’s an area you’ll be reaching around under .
I used the foam floor stuff on seats in my sailboat so the dog didn’t slide around . Mine was the grey fake teak look. It’s been two years and holding up well, it does get dirty when bugs get squished into it , but it cleans up with soap and water . And it dries up very quickly after a rain unlike carpet. There are a lot of quality levels and even companies making custom layouts. I bought mine from Amazon and it’s been good . You can seam it to make 5-8ft wide panels and it’s almost perfect .
Sent from my iPhone using GTAMotorcycle.com
I used the foam floor stuff on seats in my sailboat so the dog didn’t slide around . Mine was the grey fake teak look. It’s been two years and holding up well, it does get dirty when bugs get squished into it , but it cleans up with soap and water . And it dries up very quickly after a rain unlike carpet. There are a lot of quality levels and even companies making custom layouts. I bought mine from Amazon and it’s been good . You can seam it to make 5-8ft wide panels and it’s almost perfect .
Sent from my iPhone using GTAMotorcycle.com
Mad Mike
Well-known member
I think most small boats use 5/8" on the main floor. It's lighter and there are lots of support points I the main floor. 3/4" is used for hatch covers and foredecks as there is limited support, There are no rules so you can do what works.
The EVA foam is nice looking, I've never used it. The rubber-backed outdoor carpet is great if it's being held in place with snaps (like on a flybridge or rear deck of a cruiser), I wouldn't use it for glue down in a fishing boat. Rubber backing will eventually separate from the carpet then you get stretches and wrinkles - looks horrible. Use polyolefin outdoor carpet that has no laminated backing.
I have heard from bass boat friends that the foam degrades after 8 years or so. That is mostly in full sun though. If you are covering the boat it shpuld also longer. From similar foam on paddleboards, it will get dirty and marked up. If ypu have ocd, carpet will look new for longer.
Do you mean this stuff?
I do suffer from undiagnosed OCD.
My boat gets used 1-3 times a year and a max 5 times if we take it to a cottage. I am lucky enough to be able to store it in a covered environment where it is protected from the elements, but not rodents. The only exposure to sun that it would get is when it is being used or docked on the water, transported and when it sits on my driveway for a few days.
My storage facility is not rodent proof and that is partly whey I want to redo the existing wood and carpet. Mice are tiny and can get through a tiny holes and piss all over and leave their droppings. I have made a cover for the boat from old wood fence panels but the buggers don't need much of a hole to get through. Very difficult to make it super tight especially around the motor.
My storage is free and I paid a fraction of what this boat is worth in its current set up. I obviously don't want to blow the bank on it but make it look presentable and enjoyable to use.
If I had a $30,000 boat, I would for sure be looking at different storage options.
Any comments on the plywood the devlopers use to post proposed zoning changes? Stuff seems to last forever, zero maintenance. Thicknesses may be limited to half inch, 12 mm and something in between.
They often use MDO ( medium density overlay) , the most popular brand was Crezon so it’s often generically called that. It’s an exterior grade ply with a resin coated paper overlay. Often used for highway road signs , airport signs and used as concrete formply in low end forming jobs. 9mm/ 12mm/ 18mm and 21mm are available .
Sent from my iPhone using GTAMotorcycle.com
Sent from my iPhone using GTAMotorcycle.com
Question for the boat experts.
I was was thinking about the configuration of my boat and possibly reconfiguring IF I was to redo the plywood and carpet.
As you see in the picture, the current boat has the typical benches that you find in a aluminum shell boat. At the back of the boat and under the front deck where the front pedestal base is located. The inside of the benches is filled with styrofoam. I am not sure if this was a factory design (the styrofoam part) or if the previous owner filled the benches himself. Would removing the bench and more specifically eliminating the styrofoam have any negative effect on the boat?
I am guessing the styrofoam is there to provide more buoyancy in the even of a tip over. But I doubt that it would actually prevent the boat from sinking.
I was was thinking about the configuration of my boat and possibly reconfiguring IF I was to redo the plywood and carpet.
As you see in the picture, the current boat has the typical benches that you find in a aluminum shell boat. At the back of the boat and under the front deck where the front pedestal base is located. The inside of the benches is filled with styrofoam. I am not sure if this was a factory design (the styrofoam part) or if the previous owner filled the benches himself. Would removing the bench and more specifically eliminating the styrofoam have any negative effect on the boat?
I am guessing the styrofoam is there to provide more buoyancy in the even of a tip over. But I doubt that it would actually prevent the boat from sinking.
The styrofoam should be enough to keep the boat at the surface. If you have no foam and you happen to fill it with water, it becomes a submarine. With environmental protection laws, you need to recover the boat. On the surface, that is a tow or a buddy with a boat. As a submarine, that means you need a diver (or ROV if deep) and a barge/boat with a winch and davit.
EDIT:
That doesn't mean you have to keep the bench. When it's apart, find other places to put the foam. If you are foaming between the stringers, make sure you leave a path for water to reach the stern so you can get it out. Water will get in the bow. Soaked foam is heavy and never dries out. Best bet is to get the water away asap.
Mad Mike
Well-known member
.
You can’t remove the benches, or change seat tops to hinged lids - they are structural members that keep the boat from twisting. If structure is compromised, the rivets and plates of the boat will slowly weaken. Rivets will begin to stretch, and aluminum parts will develop cracks, you will start to notice leaking and in extreme cases catastrophic failure.
The seat cavities in small aluminum boats are designed to hold boyant material that serve 2 main purposes; preventing the boat from sinking below the surface, and providing something large and buoyant for occupants to cling to after capsizing.
Looks like the seats are staying put.
Thank you.
Thank you.
