My Terrible Tuning Experience With Pro 6 Cycle | Page 2 | GTAMotorcycle.com

My Terrible Tuning Experience With Pro 6 Cycle

Google is your friend!!! type motorcycle tuning toronto and it'll give you your choices....I personally deal with Zed at Z1 and his tuning experience is second to none (imo) over the years he has tuned 3 bikes for me and I have no complaints whatsoever and they have a proper wideband load control Dyno. I'm sure there are others in the city but if you don't know how to use the tool....its useless.

Joe




I've had very good experiences with pro 6 but found out yesterday that they did not use a wide band sensor for tuning. I was a bit dissapointed as I wanted to verify the AFR readings my Autotune was reading.

I would still shop there as they usually have great prices for certain things but would probably go to a shop that uses wideband for tuning purposes.
 
you guys got me thinking twice. I'm considering putting on a two brothers slip on exhaust on my 06 600 gixxer. I was informed that all i would need is some tunning on the Dyno, no need for any other mods or components. Any input?
 
you guys got me thinking twice. I'm considering putting on a two brothers slip on exhaust on my 06 600 gixxer. I was informed that all i would need is some tunning on the Dyno, no need for any other mods or components. Any input?
A slip-on usually doesn't require any tuning whatsoever.
 
The o6 gixxer has a catalytic converter and tailpipe as one. This will be replaced with a short section of pipe and the two brothers tip. The bike must be tuned differenty with the catalytic versus without?
I will ask in the technical section.
 
Bazzaz doesn't auto tune as you ride.It depends on user inputed cells.

Here is a question:Who in the GTA uses knock data for tuning motorcycles?Or anyone read plugs after a run?I don't know of any,maybe that's why the Bazzaz unit doesn't have ign. timing adjustablity.


Sorry about your experience,i've always had good ones with Pro 6.
 
Last edited:
The o6 gixxer has a catalytic converter and tailpipe as one. This will be replaced with a short section of pipe and the two brothers tip. The bike must be tuned differenty with the catalytic versus without?
I will ask in the technical section.

You will want to have it re-tuned after doing the slip-on. It's less of a deal if it was an older bike with just the muffler but when you delete a cat you're making a much bigger change and your fueling will need to be changed that much more.
 
you guys got me thinking twice. I'm considering putting on a two brothers slip on exhaust on my 06 600 gixxer. I was informed that all i would need is some tunning on the Dyno, no need for any other mods or components. Any input?
You can run it without any tuning but it might feel slugish on the lower RPMs..Not bad,might not even notice it if you not used to rev it.
The good thing about the 06-07s that the oem ecu is tunable so no need for PC or BAZZAZZ.
 
Bazzaz doesn't auto tune as you ride.It depends on user inputed cells.

It collects data as you ride and when you plug it in afterwards, shows the suggested changes. You can either accept or leave it. The PCV auto tune makes live changes as you ride.
 
If I could get a dollar for every time I took a bike that was complaining about their custom tune and set all fields to zero and customer leaves perfectly happy saying it runs INCREDIBLE never to have a problem again ;)
 
  • Like
Reactions: TK4
^Then they clearly didn't have their bike tuned properly!!! My bike has been flawless since the re-tune in both hot and cold temps.
 
I think what he's saying is that some "custom tunes" are good, but a lot of them are not, and it would have been better to leave the bike stock. No point having a PowerCommander if it's all set to zero. But it's even worse having one that has not been tuned properly.
 
^I understood what he was saying :) I had the same issue with the first tune at Pro 6 where I uploaded the basemap so it would run better.
 
In early June I went to Pro 6 Cycle to have my 2008 GSX-R 750 tuned after installing a full R77 Yosh exhaust, K&N filter, and Power Commander 5. After hearing some great things about their shop and reading a few great reviews I thought for sure they would be the place to get what I wanted out of my bike.

On my tune day everything seemed to go great. There was nothing that concerned them and the bike ended up making 130whp which I was more than pleased with. Under WOT the bike ran great, but in the low end something felt a little off. It was hesitate and gurgle when leaving a light, or when cruising at partial throttle. I talked with a couple people and they said it was normal for the power commander to have this issue down low. So I let it be for a few more days until we got a hot week where the temperature was above 30 degrees. This is when it got worse, and I mean really bad. The bike just ran like complete crap. Hesitating and gurgling all the time, and made virtually no low end power. After owning a boosted car for many years I knew right away that the bike had to be running rich. Sure enough I noticed the bike was smoking like crazy on acceleration and my exhaust was black! I gave Pro 6 a call and spoke with John who told me it was all because of my full exhaust and that the bike wasnt meant to make power bellow 7,000. I said that`s fine, but the bike runs like crap. It has nothing to do with power and that I was going to put on another dyno.

I had taken my bike to Orillia Motorsports when it was stock for a baseline dyno pull and I was going to put it on after my tuning at Pro 6 to see a true difference. When I took the bike there I asked him to do an AFR datalog to see if my suspicions were true. As soon as the bike started moving on the dyno it would dip in from a good 14.x AFR right down to 10.3-10.4 AFR. It sounded terrible on the dyno from idle until about 5,500 where the AFR would jump back up to around 12.0 and ended up making 131whp on his dyno in top end. It was obviously the problem was in the tuning. I called John and told him my problem. He dealt with it very well and said come in for a clean up tune at no charge. I was pleased to bring my bike back down to get this problem resolved.

So they put the bike back on the dyno and do their fuel adjustments. I take the bike around the block and sure enough it is running like crap again, but not as bad as before probably because it was a cooler day. I waited another couple days with it and once again when it got hot outside the bike was a complete disaster. It was smoking again, so I did an oil change at 2,000km's and the oil just reeked of gas. I called John back and explained the bike is still a mess, and once again he said it was normal and that it was all because of my full exhaust system. I said it nothing to do with the exhaust since the bike ran flawless with the power commander supplied BASEMAP and that it had to do with their tuning! So I put the basemap back in and the bike ran perfect. It was obviously back down in power in the top end, but it was so much more enjoyable because it wasn't running like crap. After a little while the bike stopped smoking too!!! A basemap ran much better than their 3 hour tune!

I was thinking to myself how could a shop with so much experience botch such a simple tune! So I asked John if they used a wideband for tuning.......NOPE!!..... I was shocked to hear this and said how do you tune partial throttle? Do you smell the exhaust! The top end is one thing. You can throw the fuel at it until it stops making power, then pull some back, but the low end is another thing. I told him that I will be taking the bike to another dyno to have it tuned PROPERLY with a wideband. I took it to Orillia Motorsports where I should have done it from the beginning and the bike came back PERFECT! Made the same power on a stupid hot day as Pro 6's tune, but the bike was mint down low. What a difference in response and torque and pulled so smoothly through the whole powerband. So I left Orillia Motorsports paying $180 for a perfect tune, where I paid $310 at Pro 6 for a crap one!!

I called John back and explained to him that the bike is perfect now and makes great power. I wondered if thought I was full of it, so I told him I would gladly put it on their dyno again to show them. At this point I said it would only be fair if I was given some sort of a refund. I was willing to accept up to 50% back since I only got 50% of a tune. He said this wasn't possible and that we could work something out with a store credit! Even will all of the ******** I had to go through I calmly agreed with him and said I would be down to buy some new tires in probably a month or so. So I now needed tires and asked him what I had for a store credit, and well that store credit turned into him giving me some discounts on parts. I said I don't need parts, I need tires, and he said there was nothing he could do for me. I thought in the beginning that he would have good customer service, but after putting up with this ******** for a month and having to spend more money elsewhere he basically screwed me completely over.

That's my story. Sorry it was a long one.
They are scammers.
$1210 or a tune and woolich harness.
$220 for tightening an engine mount which I checked before taking it in
5.5 hours of tuning to get two runs on a graph with zero a/f quantities.
biggest scam in the bike community.

E1C95BD4-D4FC-449B-908D-ED20C1846FC3.jpeg
 
Reminds me of a time years ago when I left my car to get a tune installed and a dyno run before and after. I came back later in the day and it was in the EXACT same spot in the parking lot where I left it. I suspect they loaded the tune while it was parked and charged me for the dyno runs that never happened.

There are a lot of shady operators in this business.
 
All this noise reminds my of one day at the track a long time ago.
A rider came into the pit lane complaining about this, that and pretty much everything.
His tuner looked him square in the eye and said "why don't you learn to ride the f*cking thing before b*tching your head off ?"
A lot of folks seem to spend their time and money busily fixing stuff that isn't broken.
Maybe get a qualified suspension setup done and taking some schools or track days instead of wasting it on dubious performance enhancements ?
 
All this noise reminds my of one day at the track a long time ago.
A rider came into the pit lane complaining about this, that and pretty much everything.
His tuner looked him square in the eye and said "why don't you learn to ride the f*cking thing before b*tching your head off ?"
A lot of folks seem to spend their time and money busily fixing stuff that isn't broken.
Maybe get a qualified suspension setup done and taking some schools or track days instead of wasting it on dubious performance enhancements ?
I agree, but what about getting a "tune" for better performance not necessarily for a massive gain in torque or HP, just better overall engine performance? I am actually asking, as I have thought of this many times.
 
I agree, but what about getting a "tune" for better performance not necessarily for a massive gain in torque or HP, just better overall engine performance? I am actually asking, as I have thought of this many times.
Or leave it stock and learn how to ride it ?
That was my point - I sincerely doubt that 99.9% of riders on the street can use the power available to them right out of the box.
Handling, tires and operator experience rate way higher in my books than an extra 10HP.
 
Or leave it stock and learn how to ride it ?
That was my point - I sincerely doubt that 99.9% of riders on the street can use the power available to them right out of the box.
Handling, tires and operator experience rate way higher in my books than an extra 10HP.
While what you say makes sense on the track, it's a mixed bag on the streets imo. You can whack open the throttle (for a very short time) and enjoy the ride legally. Is there any road in ontario that every bike sold can't easily run with cruise control on >30 km/h over the speed limit as it comes from the factory? Better suspension/tires increase the performance ceiling and may help you in an emergency situation but in most cases, you either need to increase your speed or the ride becomes even more boring and just a cruise. With 172 now hitting at 40 over on most of the fun roads, in the absence of surface contamination, any bike from the factory (except lsm) can probably get the ticket in almost every corner in Ontario (except the few hairpins).

Training/targeted experience is always a great idea as that makes the biggest difference when things go wrong.
 
If you’re slow it’s likely because you’re not carrying speed in the corner. That’s not something a tune is likely to solve.
 
They are scammers.
$1210 or a tune and woolich harness.
$220 for tightening an engine mount which I checked before taking it in
5.5 hours of tuning to get two runs on a graph with zero a/f quantities.
biggest scam in the bike community.

View attachment 50243
2hours to tighten a bolt? That's ballsy.
 

Back
Top Bottom