Search results

I think this is accurate.

I tested my buds after the bud wash, but I don't have a control. I wanted to know how much CBD was in my Caribbean Mystery, since that's what I was after, not THC. It was 12% CBD and 16% THC. The bud wash uses no harsh chemicals or agitation. It's also recommended by most professionals. You can...

I strongly disagree.

What you'll need to wash buds: Three buckets (ideally 20-litre but smaller is fine) Clean water (filtered or reverse osmosis) Lemon juice & Sodium Bicarbonate (for general cleaning) or Hydrogen Peroxide 3% (for powdery mildew) A drying line to hang the wet buds Bud-washing, a step-by-step...

If you don't mind a little work, dig out an 18" diameter by 18" deep hole for each plant. Start them in 5 gallon buckets (preferably food grade) till there get a couple feet tall. Drill 1/8 holes all over the bucket for drainage, sides and bottom. When the plants reach about two feet tall...

I’d rather see someone’s true feelings out in the open. When people speak their minds — even if it’s ugly — it shows exactly who they are. It’s like they’re putting a scarlet letter on themselves. I just make a mental note and move on. I get why you’d ignore, though.

I agree with ToSlow. I understand why people would ignore others, but I don't have a use for it. There's a few people I've found annoying, even offensive, but that's life. I don't give them much of my time. I'll quickly skim there comments, but for the most part, I use the "ignore" feature...

Well, you're usually the first to reply, react or comment, so I don't think you have. How does it work? Does it prevent them from seeing any content you post, and vice versa? Posts, comment, and reactions? Or does it just block you from seeing them?

Sorry. I'll try to do better.

Sunday I started putting my spare Kat back together. The gas tank has been off for about a year and a half, and pre-install scan found a fair bit a surface rust inside. A.I. tells me that soaking it in vinegar and salt (1 cup of salt per litre of vinegar) for a couple days will remove the rust...

When it comes to frost, I learned that temperature on weather sites are taken at 4 feet above ground level. Also, temperature can drop up to -1ºC per vertical foot. So from the 4 foot mark, the temp could drop up to -4ºC. Frost happens at 0ºC. So as long as the weather forecast calls for 5ºC or...

There's a VERY good Facebook group called Ontario Grows. A friend of mine in Barrie runs it. There are a lot of very helpful people in the group that will share all kinds of tips from living soil to pest control. I suggest you check it out no matter your experience, and especially if you are new...

It's not too late. Despite popular opinion, you don't have to have the biggest plant. If I remember right, the limit is 4 plants outdoors, if you're not licensed. You'll still get a good 6-foot plant by harvest if you start now.

Back in 2021, I have 8 Caribbean Mystery plants in my yard. The largest hit about 9 feet tall and had buds the size of a Nerf football. Three days before my planned harvest someone jumped my fence and stole 6 of them (and left a Maximum claw hammer on the ground). Luckily, I harvested one the...

That would be a dream final. Canada could use it. It would be Leafs fans against the rest of Canada and USA hockey fans because as we know, if you aren't a Leafs fan, your a Leafs hater. The Leafs are nobody's second-favourite team.

I was considering leaving the bike off the road for next summer anyway because I plan to do this rebuild, and since the engine is out, and I've had most of the bike taken apart several times already before, I might just do a full restoration. The fairing will be off, the engine out... I might...

I called around about getting the engine rebuilt professionally. Two places quoted me $10,000. My jaw hit the floor. I already spent a couple thousand on luggage for the bike. Luggage isn't an option, even through aftermarket for this bike. I bought full Givi Outback, and mounting brackets for...

So, a piece of polished marble should work? It doesn't flex, and is machine ground and polished. And very strong. Do I understand this right? I would use an abrasive, like an adhesive sandpaper, with the flat surface to sand the machined surface perfectly flat?

Thanks.