Search results

Prety sure these are the ones like on mine. http://www.heidentuning.com/p/28/2404/mo74-cg%7C25=4/%2348-5011-fuel-idle-mixture-screw-with-spring-washer-and-o-ring

Yeah i think all mikuni's are pretty much the same. I got 36's on my bike and they are the same like the 38's and 40s.

It's a mikuni carb right? Bst 32 i think the specs are the same for all mikuni carbs. lemme check

Don't think winners circle will have anything. Not sure how much your looking to spend but Factory Pro has the long extended mixture screws for most carbs.

I usually cut a slot into stuff like this then use and impact driver. If that doesn't work I use a left handed set of drill bits( Counter Clockwise). Usually once I am half way through the bolt it ends up spinning off.

One method I use when I sync carbs that helps is I use the tip of a sewing needle and i adjust the butterfly so that the tip of the needle just drags underneath the butterfly and the inlet shaft. I can get them all pretty close. You start with carbs 1 and 2 then 3,4. And then 2 and 3. They...

1. Yes, Smooth throttle roll on. 2. Target fixation, look where you want to go. 3.Sometimes wave. 4.Just ignore it 5. Look where you want to go, don't be a ****** bag.

http://www.kijiji.ca/v-sport-bikes/mississauga-peel-region/yamaha-r6/1077534243?enableSearchNavigationFlag=true http://www.kijiji.ca/v-sport-bikes/city-of-toronto/2009-yamaha-yzf-r6-v1704-dont-pay-until-2016/1076780144?enableSearchNavigationFlag=true

Thanks for the advise guys, just installed them last night. Axle slides through the bottom like butter and everything is aligned perfect. Right fork is 37.5mm above top plate and left came in at 38mm. Less than 1mm is acceptable. Put new bearings in. should be like brand new.

So my girlfriend is buying a motorcycle from a friend of ours. Essentially the sale price is what we want it to be. Now its my understanding that there is no formal taxation mandate on motorcycles as there is on cars. If our friend writes a receipt for x amount for sale of the motorcycle ...

Thanks for the advise guys. Very informative write up on the bmw page and a great insight. I think from everything that I have read the most important factor is that there is no binding at the front axle. Also due to machining factors one tube may be 1mm higher than the other in their...

Hey guys, I wanted to discuss the different methods used to align our forks when putting them back in. I just got the full race treatment on them and want them to go in perfect. So we have 3 horizontal planes and 2 vertical ones in all to consider when installing the forks. Anyone of those...

Up for sale is a pair of Ultimate Size 8 Boots and a pair of Joe Rocket M/L gloves in good shape. $80 for the lot. Please call or text Ashley. 647-888-3387. No emails please. Thanks. $80 for the lot. Please call or text Ashley. 647-888-3387. No emails please. Thanks.

Found. Please remove.

Looking for Ninja 300 fairings in Black. Looking primarily for mid right and upper. Also the right insert. I would be interested in buying a complete 300 body as well. Thanks

I have used a rear stand and jack stands. Lower the bike onto the jack stands resting on the lower rails. I have used this to do swingarm swaps and rear shock swaps.

Thanks guys, theres about 8000km or so on this tire. Im not too worried about it. I rebuilding everything from the steering stems down including the forks so should be like brand new again. Probably going with the BT16 PRO tire. Good reviews and good price. Going to try the balance beads as...

Looking for hayabusa master cylinders. Clutch and/or brake master cylinder. 99-2007. Thanks.

Thanks for the replies guys, Yes Maybe I am just turning left more. I was going to get new tires this season. I was infact looking at petes superbike. Any suggestions on tires? Bike is a 90 gsxr 1100. Its ported head, jet kit, exhaust, the whole deal. I mostly ride street but wouldn't mind...

I have been riding since 2009 but first time encountering this. Upon close inspection of my front tire I noticed some uneven tire wear. The only thing that comes to mind is a failing right fork seal might have lead to the uneven wear. I know this because I am rebuilding my forks and the right...