Bringing Her Back to Life | Page 12 | GTAMotorcycle.com

Bringing Her Back to Life

It's a vac petcock. I have the vac hooked up. It will run for a bit on the vac, but the fuel will stop after a while.
 
Look what arrived the other day. Just need a fan for it now.

662f177dc039e0d0ef0b4b2535b5fd7d.jpg
 
Ok, been braving the cold and decided on some bike work.

I thought I'd redneck myself a clear clutch cover. It's not installed yet. I now have to strip the case, repaint and change all the seals/bearings.

Some pics of what I did.

3c1a0bcecb5274cf2dc673f1d5ed77b9.jpg


38900566e1e24489b287ef06fb095b7c.jpg


d946aec2219baab78baba21223a45e1b.jpg


4a1268cc65193e1dc0bc510701b519df.jpg


7fc0ad5b159f9de08f158ee64d9c7523.jpg


e1eb57d55d2d54edaf16a0abbfd498a1.jpg


bdc7962f1b16c53c292a84be341921e7.jpg


285490e737a3866c781f403d0bbe0d4d.jpg


64d9c10e3976157b489e1db8662fc9eb.jpg


257a5350a80172e154cfc2fcc448e7e6.jpg
 
I thought this might just be easier for you to see. Don't k ow why I couldn't send pics to your phone?
 
Thanks guys. I need to finish it with a metal ring

5d26618b43b08763126e62cb3740599a.jpg
 
You should mill a slot for an o-ring seal

This will just be a retaining ring. The sealing surface will be between the lexan and the case.

I'm just going to buy some thin, rubber, sheet gasket material and trace one out.

If I had access to a lathe, I might consider it. Plus, I wanted to show guys that there are easy mods out there that can be done with some basic tools.
 
This will just be a retaining ring. The sealing surface will be between the lexan and the case.

I'm just going to buy some thin, rubber, sheet gasket material and trace one out.

If I had access to a lathe, I might consider it. Plus, I wanted to show guys that there are easy mods out there that can be done with some basic tools.

Sorry I have 3 CNC routers so for me milling is less work then what your doing with that hand held router. I guess if you want to do it all in house then no fancy equipment and machining

Would be cool though I'd like to engrave some plexi glass like that. I could engrave names, graphics, etc
 
Got the cover together. It turned out decent, but I have other issues.

0bc549ffd4c5bac63a5066fcbb7daa62.jpg


I have some horrid clutch shudder when hard on the gas from a stop. I had the case off, so I dove into it. I thought I had a lot of slop in the clutch cush/damper. Decided to tear into it and rebuild it.

Drilled out the rivets to get to the old pucks. Decided to replace the pucks. The OEM setup was 4 pairs of pucks. One big, one small for each set. I'm going with all large ones.

4005210c366dd63d181e6bd22164499b.jpg


To get this unit back together, I drilled out the holes in the 4 bosses to accept 8mm bolts. They will need to be cut back once installed (with locktite)

9787a94a9d567cc08262daf4b3c6a911.jpg


The worst part is that I can't drill/tap the hardened plate. I need a 6.8mm (tap drill size) carbide bit as well as a high quality 8mm tap.

a9f6cee27a551b10d53550ccbe02a944.jpg
 
Started it today! Seems to run good. Still having some electrical issues.

It smokes. I was worried about that considering I swapped the pump from one case to the other.

ec96b704d24bb4c3b989da249d8bd49c.jpg

I cleared the neighbourhood of bugs. Lol
 
Started hearing ticking from the bottom end. Not sure if it is caused by interference from my new bolts that I have installed to replace the rivets.

I've torn it apart and trimmed them perfectly flush now. I have the basket back in and torqued. Should be able to get the clutch plates and fibers in tomorrow.
 
Awesome now we are going to have similar clutches, I am converting mine back to the wet clutch because my dry clutch ****** out oil, we will both have the see-through glass on the case lol!
 
Cool. We'll be samies - except your bike will be faster and newer. Lol
 

Back
Top Bottom