My GS500 "Streetfighter/Bobber" Build "Becky-Lynne" | GTAMotorcycle.com

My GS500 "Streetfighter/Bobber" Build "Becky-Lynne"

ShanehSMP

Member
Picked this bike up last November from a seller on Kijiji. This is my first bike. I've always liked the look of naked bikes over faired bikes. Wanted to start small so that my insurance premiums would remain low...also, I don't think I'd want to learn on a bike with 600cc + type power.

The bike as I bought it:
388356_10100112224762581_11005638_44220041_1416502098_n.jpg


The Goal is to have her looking similar to this...
423593_10100185597508011_11005638_44555592_834720942_n.jpg


The bike after I started wrenching on it:
375447_10100110904583231_11005638_44215442_520863915_n.jpg



385156_10100111526911081_11005638_44217484_1395420000_n.jpg


Took out the engine and all wiring while the weather was still warm. Then brought it inside to start the winter modifications.

This is the bike indoors:

392121_10100126190500131_11005638_44300054_101947493_n.jpg



Picked this up on ebay for $350 US. 04/05 GSXR 600/750 Front End.
382663_10100112221778561_11005638_44220034_381631649_n.jpg

Came with everything I needed on the front end (except upper triple)...tire isn't good for the road, but will make a good track tire if anyone is interested in it. Michelin Pilot __? I believe.

Sent the triples out to a guy to get a spacer made and the GS stem pressed into the GSXR lower triple.

More pics to come...I've got limited funds at the moment, due to other more pressing obligations but I will update this thread as the project progresses.

BTW, if anyone in the GTA area can recommend a good machinist or welder let me know.

Thanks

-Shane
 
Last edited:
Oops, forgot to mention my plans for the bike.

Kinda in this order:
-Cut the subframe shorter; remove lower bracing and re-weld diagonal canti-lever beams.
-Scruff frame/prime/paint black
-Fit the front seat of a Hyosung gt250 onto the frame.
-Fit a bandit 400 hugger onto the swingarm (in the mail)
-Fit a 07 R6 rear shock (in the mail)
-Fit wider 160/60/17 tires onto a '03 GSX600 wheel fit it to the swingarm (have the wheel, need the tires)
-Find a chin spoiler somewhere...
-New Speedo.....no clue as of yet Acewell/Koso
-New light assembly(all around).....no clue as of yet
-Paint all plastics and Tank White...
-Find a gold MX Handlebar and bar-risers to match
-K&N Filter
-Clean and Re-Jet Carbs (no clue what-so-ever how to do this)
-Odds and Ends - pegs, longer front brake lines, grips,
 
nice, i love these 'budget' builds, shows that you don't have to spend a **** load of money to get a decent bike. will be checking for updates!
 
ooooo....nice...keep up the pics...love watching these things come to life...i love seeing things come to life from so many different parts...
 
sweeeeet. love the list of mods you got planned. I really want to do the R1 tail, but don't have any fabrication experience

my bike is going through something similar... http://gstwins.com/gsboard/index.php?topic=58502.0

I hate this list...I didn't think it would be so long before I bought the bike, but then I got to searching and kept seeing more and more things I wanted to do....ah well. Such it life.

AS for the R1 tail, I don't think it would be so hard...however, if I had your style tail, I'd leave it as is. Maybe modify shorten the tail by cutting off a few inches and do some "plastic welding", bondo etc to make it look factory.

When the time comes, I'm going to come to you for some info on the carbs...I plan on running a K&N box filter and a new exhaust setup
 
I hate this list...I didn't think it would be so long before I bought the bike, but then I got to searching and kept seeing more and more things I wanted to do....ah well. Such it life.

:lmao:that'll happen. When I got mine, the list was pretty long as well, but I'm nearing the end now, so there is hope for you. I got my new carb jets heading my way in the mail, I got a Jardine RT-1 full system and a K&N lunchbox ready and waiting to be put on the bike.

I think the only performance-related mod that I really want to do still is iridium spark plugs, I'll probably order those soon and get them installed at the same time that I do my exhaust/rejet. Maybe sometime down the road I'll get a Katana 160 rear tire and shock:agave:

But yea.. it'll be my first time heading into the carbs.. so it'll be a big learning experience. I read through GStwins and the gstwins.wiki and all the info pointed to 20/65/145 jets for a full exhaust system and K&N lunchbox, so that's what I ordered, we'll see how it goes.

Give me a shout if you have any questions, or whenever you're ready to rejet and we'll get it done

EDIT: ****! I just noticed you have a GSX-R front end (was lookin at the thread on my phone earlier, must've missed it)... now I'm stupid jealous. I have to add that to my list of mods now... thanks for that. I'll send you the bill
 
Last edited:
Made some progress over the last few days....finally picked up some parts I had waiting for me in Niagara Falls...

422609_10100190937282061_11005638_44576101_1824687123_n.jpg

432006_10100219072942971_11005638_44706674_778290748_n.jpg


So I got to cutting after I picked up some power tools this weekend....As you can see, the Hyosung 250 seat that I bought didn't quite wrap around the tank so I had to remove some material. Still not a good fit, but I will figure it out when I get there.

You can also notice the new rear shock from a Yamaha 07 R6 (not R6s as I read elsewhere)....perfect fit(does apparently raise the tail end about 2")...if you do this mod, make sure that you get the metal bushing from the original linkage as they slide right into the GS500 linkage.

I might cut off the remaining metal from the lower subframe...I still don't know what I'll be doing with it yet...I'm thinking I want the lower subframe to "round" upwards, starting from the main frame and welded right below where the back of the new upper subframe is.

I'm pretty happy with the angle of the seat...I'm going to mock up a subframe out of 3/4" wood and see how it is before I get it to a welder.



426331_10100219073551751_11005638_44706678_2004102576_n.jpg


427105_10100219073781291_11005638_44706679_1116632886_n.jpg



423671_10100219074050751_11005638_44706681_72800393_n.jpg




More to come soon....
 
When do we get to see the Bob in this Bobber Build?
 
Crap this is cool. Can't wait to see it finished.

Do you still have the gs seat? If so can I have it???
 
...der, sorry should have taken a closer look. I don't think it will at all. Thanks:)
 
quick update....partially mounted the handlebar risers. If you look closely in the pic, you will see a huge gap between the riser and triple. The riser was meant for a special triple and came with special bolts. I need to somehow find a M12 x 1.25 x 30 to 35mm hex socket bolt.

I also threw on the MX handlebar to get a feel of the layout...it's a little wide, might cut it down an inch or so.

Did a little work to the seat, I designed the upper part of the subframe using 3/4" wood strips, just need to have them welded now.

420235_10100222085306171_11005638_44723903_1581300063_n.jpg



If anyone can recommend me a welder, I'd be grateful.

Thanks
 
Sweet headlight.. can't wait to see it mounted.

A 150 or 160 rear??? Did you do the Katana swap or something?
 
ooooo....nice...keep up the pics...love watching these things come to life...i love seeing things come to life from so many different parts...

Agreed, love these types of posts about DIY projects.

To the OP, good luck, keep the group here updated.
 
Looks great man...
Silly question, why didn't you powder coat the frame?
It would look dope as **** if it was black.
 
Sweet headlight.. can't wait to see it mounted.

A 150 or 160 rear??? Did you do the Katana swap or something?

Yea, I've got the Katana wheel ready to go...Need to do more research on tires before I purchase...


Looks great man...
Silly question, why didn't you powder coat the frame?
It would look dope as **** if it was black.

Yea, I plan on painting/coating (if money permits) it all black after I weld the subframe and position all necessary holes...don't want to get it scratched up before she's ridden...

still far as hell to go...and I haven't even taken my m1 yet...
 
I was knee-deep in my bike today.. got the rejet done and out of the way with. So if you need a hand when doing yours, just give me a shout
 

Back
Top Bottom