I believe you have to rebuild the calipers because they need to be cleaned right out, and replace the lines.
|
So my new (old) race bike has dot5 in it. Whats the best (EASIEST) way to go about flushing and cleaning all the old fluid out before adding the new dot3? It's a 99 R6
Last edited by kellen; 03-21-2012 at 12:13 AM.
I believe you have to rebuild the calipers because they need to be cleaned right out, and replace the lines.
Well ain't that a *****. i'm not really down with that.
Yea.. something like Dot 3/4 don't mix with Dot 5, but you can mix with Dot 5.1.
Like oil and water!
Ecto • 2006 Honda VeeFourRoad 800A (Pearl Black)
I'm too sexy for my turban.
yeah maybe it's just easier to clean out the new master and keep using dot 5
Without sounding a smarty pants I really would refer to the manufacturers websites. If they don't give an answer then get in contact with their tech support. Brakes aren'ty something we want to be second guessing about.
I recently started using 5.1, although I was rebuilding my calipers and installing a new master, new reservoir and fitting new braided lines at the same time so really didn't have to worry.
Spineless swines. Cemented minds.
So I got a little curious and did some research. This part stood out to me.
Dot 3 being glycol
Dot 5 being silicone
"On the practical side, beware that glycol and silicone brake fluids are hugely incompatible with each other. Mixing even small amounts will create a sludge that looks amazingly like Italian salad dressing and is about as effective as a brake fluid -- meaning, not. Of further consideration is that, in some cases, the hardware designed for one fluid will not accept the other. Brake caliper and master cylinder seals, hoses, and other parts won't always work correctly when the type of fluid is changed."
Source: http://www.motorcycleproject.com/mot...rakefluid.html
Ecto • 2006 Honda VeeFourRoad 800A (Pearl Black)
I'm too sexy for my turban.
Why would u even think dot 3? why not 4?
Resident Loudmouth
You don't need working brakes in lost era.
This is not a black art.
DOT 3, 4, and 5.1 are all compatible with each other.
DOT 5 is not compatible with any of the above.
Switching from one type to the other requires a complete clean & rebuild of the system. Worst case scenario - your calipers fill with goo and suddenly don't work so hot.
If the OP plans to continue using this as a racebike, you're better off to continue using DOT 5. It's not so great for street use as water can collect in the bottom of the system. It is however legal, and some Harleys came with it from the factory.
1996 Kawasaki ZX11D - "When I'm on the road, I'm indestructible. No one can stop me ... but they try."
I didn't say it was a black art. I suggested he get advice from the manufacturers rather than from an internet forum, simply because brakes are crucial bits of equipment. And that was just my view, not the definitive answer. And even though you sound extremely well educated regarding the subject, even if I knew you and you were stood in my garage advising me, i'd still sneak off and check with the manufacturers.
Spineless swines. Cemented minds.
If ti has 5 now I would just stay with 5.
Brembo master i want to install was used with a dot 3 system.
Sent from my SGH-I896 using Tapatalk
I can think of once instance where I would use DOT 3 over DOT 4. Ford HD DOT 3 is an inexpensive brake fluid that has a higher dry boiling point (550 degrees F) than most DOT 4 fluids, *BUT* it has worse a wet boiling point, which leads to its DOT 3 classification. If you change it frequently, its a great track day brake fluid.
See that is the kicker, the master you want to use was used with DOT3, but caliper and lines you want to put it on were used with DOT5... So either you are converting the calipers and lines or you are converting the master... either way...
Easiest path to me is just don't switch the master (is your's dead)?
Bookmarks