Rattle can paint for race glass?

[FriendlyFoe]

I tend to fall down lots so i figured i'd paint my own fairings. I'm wondering what sort of rattle can paint in a full gloss thats suitable for spraying fiberglass, as im thinking i'll need something with a bit of flex agent in it? What should i use and where can i get it?

Thanks!

[caboose483]

any automotive spray paint will work. Canadian Tire.

keep in mind that if you ever do want to get a real paint job for it, you'll have to remove all the spray paint before laying on the good stuff.

[inreb]

You might want to look into Krylon Fusion plastic paint. I've used it on dirt bike plastic with good success. It's an idea, anyway.

[omnivore]

Be sure to use an automotive grade clear over the tank. My buddy didn't and every drop of gas on fillups left sticky smears in the paint on his fuel tank....which also smeared onto his leathers when racing./

[mxs]

How do you want to use two stage gasoline resistant clear coat (any other cler coat will not resist gasoline as far as I know) over CT spray can stuff? I was always told by the paint shops that you cannot do that, because the two stage clear coat will lift it ... not speaking about the fact that breathing the two stage stuff is not good for you ....

[FriendlyFoe]

How do you want to use two stage gasoline resistant clear coat (any other cler coat will not resist gasoline as far as I know) over CT spray can stuff? I was always told by the paint shops that you cannot do that, because the two stage clear coat will lift it ... not speaking about the fact that breathing the two stage stuff is not good for you ....

Maybe i cant, the design i'm going to go with the tank will be a solid colour either black or white so if i need to have the tank painted professionally so be it.

[fsilva_mcl]

Always try to do the left side of the bike better....for pics of course

+100000 hahaha

My boot would rub the paint off my tail fairing so I'd always touch up the left side first, if time permitted I'd also do the right...

And I used krylon from Canadian tire. We originally used the expensive stuff from the paint shop with a gun first but then decided to switch to krylon which ended up being more durable and a lot cheaper.

[Yamaha_Gurl]

+100000 hahaha

My boot would rub the paint off my tail fairing so I'd always touch up the left side first, if time permitted I'd also do the right...

And I used krylon from Canadian tire. We originally used the expensive stuff from the paint shop with a gun first but then decided to switch to krylon which ended up being more durable and a lot cheaper.

Your bike is SO bad that I even p-chopped the paint scratches out of it! lol Can't wait to not have to do that with your new bike!

[fsilva_mcl]

Your bike is SO bad that I even p-chopped the paint scratches out of it! lol Can't wait to not have to do that with your new bike!

My bike takes offense to this comment....

[CBRJOHN]

You might want to look into Krylon Fusion plastic paint. I've used it on dirt bike plastic with good success. It's an idea, anyway.

DO NOT use Krylon fusion if you ever plan on painting it properly using a automotive catalyzed urethane paint system. If you try painting over fusion it will bubble even if fully cured. It needs to be completely stripped which is a PITA. Better to stick with a lacquer / Clear system.

[RobVN]

DO NOT use Krylon fusion if you ever plan on painting it properly using a automotive catalyzed urethane paint system. If you try painting over fusion it will bubble even if fully cured. It needs to be completely stripped which is a PITA. Better to stick with a lacquer / Clear system.

Ok I'm gonna ask here; I've painted mine with automotive lacquer and it has a satin like finish which is not exactly smooth. To have a nice say shiny smooth finish, do I need to apply a clear coat; will this do the job. Thanks

[CBRJOHN]

You might want to look into Krylon Fusion plastic paint. I've used it on dirt bike plastic with good success. It's an idea, anyway.

Ok I'm gonna ask here; I've painted mine with automotive lacquer and it has a satin like finish which is not exactly smooth. To have a nice say shiny smooth finish, do I need to apply a clear coat; will this do the job. Thanks

If it's not smooth and provided you have decent film thickness you can wet sand it with 600+ grit wet dry sandpaper over a foam sanding block then spray it with a clear coat. I've had good results with Dupli Color clear top coat which is a acrylic lacquer clear. Just don't expect the durability to be on par with catalyzed urethane clears.

The best results that are more economical than automotive base clear systems was with Nason one step urethane and using a integrated clear final coat. But those systems are going away in favor of water based systems.

[RobVN]

If it's not smooth and provided you have decent film thickness you can wet sand it with 600+ grit wet dry sandpaper over a foam sanding block then spray it with a clear coat. I've had good results with Dupli Color clear top coat which is a acrylic lacquer clear. Just don't expect the durability to be on par with catalyzed urethane clears.

The best results that are more economical than automotive base clear systems was with Nason one step urethane and using a integrated clear final coat. But those systems are going away in favor of water based systems.

Sorry for not getting back to this. Thanks for your info here CBRJohn. The paint I used was the Dupli Color lacquer paint. It does not have a smooth finish so if you try and use the suction cup attachment for the Gopro it does not hold. So by sanding and applying the Dupli Color clear you say it will be smooth enough for the suction cup to stick? I was getting a bit frustrated and was going to paint over it with the Krylon but now I'm rethinking that idea.

[Metastable]

You need to have a clear if you want to put on a go pro. Plus you can't put Plexus or wax or anything like that either. Wash with Rubbing Alcohol and apply it during hot temperatures for best results.

[dyno]

Nice conversation, this is exactly one and only information which I was looking for...So Its my pleasure to have this thread.
Thanks for sharing...

Glad to help

[iegod]

How does the Tremclad method hold up long term? A year later, two years later?

[dyno]

I used a can or Tremclad and a foam rolller, turned out better than I expected.. Smooth finish and no clear coat required. Looks like it was spayed.
I found a thread from a guy that described how to paint a car with a roller, Search $50 pain job on the internet and you'll find all kinds of info.
Here is the original thread http://board.moparts.org/ubbthreads/...0&fpart=1&vc=1
Here's a picture of his car painted with a roller



The nice thing about this is you can paint in the comfort of your home over winter,
I just finished painting my entire track bike in my basement without any mess.

[Jia]

I used a can or Tremclad and a foam rolller, turned out better than I expected.. Smooth finish and no clear coat required. Looks like it was spayed.
I found a thread from a guy that described how to paint a car with a roller, Search $50 pain job on the internet and you'll find all kinds of info.
Here is the original thread http://board.moparts.org/ubbthreads/...0&fpart=1&vc=1
Here's a picture of his car painted with a roller



The nice thing about this is you can paint in the comfort of your home over winter,
I just finished painting my entire track bike in my basement without any mess.

That's interesting, read a bit of the thread. But that paint is for metal, not sure if it that technique works for fiberglass and if it does, what paint to use.

[mxs]

The same paint and the same technique, it's mentioned in the thread, not sure what page. Apparently it's a big hit to use on boats with a fiberglass hull.

[Metastable]

Guys, just make sure you are not using automotive paints that contain/release cyanates. The best respirators in the world do not filter that stuff out. That is why you often see guys applying that stuff using a "positive pressure" respiration system. In other words, they have fresh air coming from the outside of the paint booth and it is fired into the mask at a higher pressure than ambient. Therefore, no ambient air can go inwards. Cyanates = not good for you.